Table of Contents
What Are Thread Classes?
Thread classes designate the fit of a specific fastener. When talking about Unified inch screw threads, there exists six standard classes of fit: 1B, 2B, 3B, 1A, 2A, and 3A. A lower class number designates a looser fit and a higher number designates a tighter fit [1]. The class letter 'A' determines an external thread such as on a bolt and the letter 'B' determines an internal thread such as on a nut [1]. These are all considered clearance fit because they provide an assembly without interference whereas a interference fit would allow positive interference of the screw with the hole. An example of a UNF series thread's designation can be seen in Figure 1.
There also exists metric variants of these thread classes. They can be seen in Figure 3 to the right with the corresponding UNF Series to the left. The letter signifies the thread band (lower case for external threads and upper case for internal threads) and the number signifies the tolerance grade, a higher number being a looser fit and a lower number being a tighter fit. Metric threads have an additional feature where they can state a tolerance grade and position for both the pitch diameter and the major diameter for external product threads and minor diameter for internal product threads [2]. An example of a metric thread's designation can be seen in Figure 2.
Figure 1. UNF Thread [2] | Figure 2. Metric Thread [2] |
Figure 3. Thread Classes [2] |
Screw Thread Fundamentals
Screw thread
Defined as a ridge of uniform section in form of a helix on the inside or outside of a cylinder.
Thread Form
Configuration of the thread in an axial plane composed of the crest, root, and flank. At the top of the threads are the crest, at the bottom are the roots and in between them are the flanks. The triangle created when extending the thread profile at a point on both the crest and root is called the fundamental triangle.
Figure 4. Components of a Thread [1] |
Thread Pitch
The distance between two points measured parallel to the thread axis is the thread pitch. Unified screw threads are designated in threads per inch which is the number of threads in one inch of the thread.
Figure 5. Thread Pitch [1] |
Internal vs External Threads
Internal threads are bolt, studs or screw threads while internal threads are the threads on the nut, or tapped holes that goes on the bolt. On internal threads, the minor diameter is the diameter of the thread from root to root, while the major diameter is the diameter from crest to crest. The pitch diameter is the theoretical diameter of a cylinder that passes through the threads such that the distance between the crest and roots is equal. In an ideal product, this should be equal to one-half of the thread pitch.
Figure 6. External vs Internal [1] |
Flank Angle
Thread Fit
Unified Inch Screw Thread
There are six standard classes of fit for Unified screw inch threads, 1B, 2B and 3B for internal threads, and 1A, 2A, and 3A for external threads.
Classes 1A and 1B | Classes 2A and 2B | Classes 3A and 3B |
---|---|---|
These include threads of extremely loose fit. This thread class is rarely used or specified in any commercial or industrial environments. They are not meant as a permanent solution to any structures due to safety purposes and are only used for quick and easy assembly. | Threads of this fit offer optimal fit. They are a balance between performance, manufacturing, cost and convenience. About 90% of all industrial and commercial fasteners use this class of fit. Most fasteners sold at any major retailer would be found at this thread fit. | Threads of class 3 are best suited where strict tolerances and strength are required. Therefore they are mostly used when safety is a critical design consideration. An instance of this thread fit would be socket caps and socket set screws [1]. |
Thread Series
In the Unified screw thread system, there are three important standard thread series for fasteners, UNC/UNRC (coarse), UNF/UNRF (fine), and 8-UN (8 thread). [1]
Fine | Coarse | 8 Thread |
---|---|---|
|
|
|
Figure 7. Fine vs Coarse Thread [1] |